Installation Manual For Mini High Speed Dome Camera Please read the operation manual carefully before installing and using
- 7 - DISPLAY: to ON/OFF the display of the DOME LABEL on the screen. POSITION: to select the display position of the DOME LABEL on the
- 8 - AMOUNT: to select the value of the EXPOSURE COMPENSATION: -7 +7. RETURN: return to the previous menu. 2.5 MOTION SETUP: enter the submenu
- 9 - PATROL: enter the submenu of the cruising tracks PATROL . PATROL NO: to select the number of the PATROL. EDIT PATROL: to edit the pat
- 10 - CLEAR ALL PATTERNS: to clear all the PATTERNS. RETURN: return to the previous menu. EDIT DOME LABEL: to edit the label of the d
- 11 - PARK TIME: to set the PARK TIME of the AUTO HOME, from 1 – 99 minutes. The PARK TIME means the blank time of the dome camera without any co
- 12 - LANGUAGE: to select the language of this dome camera: ENGLISH or CHINESE. SET NORTH: to set the NORTH direction. The dome ca
- 13 - III Setup of the Dome Camera 3.1 Connection of the System 3.2 The Figures of ID and protocol dip switcher. Figure1 10-bit dip switcher: D
- 14 - 3.3 Dip Switch The code sheet: Dome Address Status DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6 DIP-7 DIP-8 DIP-9 DIP-10 1 ON OFF OFF OFF
- 15 - 3.4 Protocol and the Default Baud Rate The SW2 is used to set the protocol of communication and the baud rate used by the dome camera. DIP-4
- 16 - 3.5 Setup of the Baud Rate As shown in the Figure, SW2 is used to set the protocol of communication and the baud rate used by the dome camera
SAFETY PRECAUTIONS CAUTIONRI SK OF ELECTRICSHOCK. DO NOT OPEN!CAUTION:TO REDUCE THE RI SK OF ELECTRI CAL SHOCK, DO DOTOPEN COVERS.
- 17 - . Description of Installation 4.1 Safety Measure 4.1.1 The requirement of the installation and service personnel. With the qualificatio
- 18 - 4.4 Preparation 4.4.1 Basic requirement Please abide the latest electric, fireproofing and other related regulations. Please check
- 19 - b) Wall installation Figure 4 Fi
- 20 - Figure 8 Figure 9 e) Finally fix the camera bottom bo
- 21 - e) Finally fix the camera bottom pedestal board and camera connecting board with M3 Screw. 3) Steps of outdoor wall Installation. a) Unpa
- 22 - Figure16 4.7 The taking aparts ways for the black cover 1) The taking aparts ways
- 23 - Figure 19 Figure 20 4.8 The installing ways for the camera 1) Th
- 25 - 3) The Installing way of Sony CNB.12X camera a) Take out Sony cameramake it that Camera on hole B alignment camera mounting panel hole A
- 26 - 4.9 Connect the control cable as Figure 28. Figure 28 Identifier of the alarm lines as Figure 29: Figure 29 Notice 1: the signal of th
Contents Notice ………………………………………………………………….……………………….1 I Description of Functions…………………..………………………………………………2 1.1 Dome Specification…………………………
- 27 - Appendix I .Troubleshooting Problems Possible Causes Remedies No action when power is switched on Power supply fault Replace Bad connecti
- 28 - Appendix ⅡⅡⅡⅡ: Cleaning of the transparent cover
- 29 - Appendix ⅢⅢⅢⅢ. RS485 Bus Basic Knowledge 1. Connection and termination resistor The RS485 standards require a daisy-chain connection
- 1 -Notice Please read this manual carefully, before you install and use the dome camera. Electric safety Please act on the national electric st
- 2 -I. Description of Functions The intelligent dome camera is a hi-tech CCTV product which incorporates high-clarity color camera, panoramic spee
- 3 -1.2 Camera Specification Camera 2000-Z Color Synchronization Internal Image sensor 1/3 Color CCD Scan system 2:1 interval line scan Horizontal
- 4 -1.3 Dome Functions Multi protocol decoder integrated a. built-in the multi protocol decoder, including maximum 16 protocols with optional
- 5 -II. Setup of the Menu of the Dome Camera Basic Operation of the Menu Open the main menu of the setup by the control keyboard or by the matri
- 6 - RESERVED: Blank. ALARM SETUP: enter the submenu of the Alarm setup. ALARM NO: to select the alarm number, from 1 to 4. ACTION: to s
Commentaires sur ces manuels